<progress id="0wt4g"><track id="0wt4g"><rt id="0wt4g"></rt></track></progress><dd id="0wt4g"></dd>

<em id="0wt4g"><acronym id="0wt4g"><input id="0wt4g"></input></acronym></em>

  • <th id="0wt4g"><pre id="0wt4g"></pre></th><span id="0wt4g"><pre id="0wt4g"></pre></span>
    1. 
      <dd id="0wt4g"></dd>
      <tbody id="0wt4g"></tbody>
    2. 產品搜索

      首頁 > 產品中心 > 空壓機氣源系列空壓機氣源系列

      吸附式干燥機

      吸附式干燥機

      產品特點 Product features

      ※具有穩定一致的出氣壓力和露點

      1.吸附塔之高度與直徑經實驗結果精密計算,塔床阻力小,保證了壓縮氣體干燥劑5秒的接觸時間,滿足成品氣的露點要求。

      2.30%的干燥劑余量,用于補償干燥劑的自然老化,確保干燥。

      3.大型擴散器,確保氣流均勻通過干燥劑層,消除溝流現象。

      ※再生氣量損耗小于14

      1.卓越的機筒設計,保存100%的吸附熱量,儲存的熱量用于增加再生階段的再生氣溫度,提高設備的解吸能力,使得再生更徹底。

      2.干燥和再生采用反向對流方案,濕空氣流過干的吸附劑時效果最佳。再生氣出口含濕量控制在亞飽和狀態,使消聲器及排氣通道無結露之慮。

      3.可根據干燥機的運行負載需求調節再生氣用量,確保再生氣流連續穩定,再生壓力低至臨界。

      ※干燥劑使用壽命長

      1.合適的機筒尺寸,使氣體通過干燥劑層的流速和時間保持最佳狀態,充分發揮干燥劑的性能。

      2.合理的系統配置,在氣流進入機筒前,經高效除油處理及時清除氣流中內含油物與重污染物,避免干燥劑層受污染。

      ※設備采用了新穎高品質電動及氣動閥和先進可靠的全電子可編程序控制器,人機界面友好,自動連續顯示雙塔工況,循環周期現場可編,出廠設定10min。閥門壽命長達50萬次動作。

      ※筒體內壁作冷鍍鋅防銹處理,10年不銹蝕。

      ※動作準確、性能穩定、操作簡便,安裝無需基礎。

       

      Bend it out on the same has the stable pressure and dew point

      1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

      2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

      3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

      Bend the gas loss less than 14% renewable

      1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

      2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

      3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

      Bend desiccant long service life

      1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

      2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

      The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

      Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

      Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

       

      工況條件與技術指標 Working condition and technical indexes

      額定進氣溫度Rated the inlet temperature

      50

      額定工作壓力 Rated pressure

      0.7 MPa0.4~1.0 MPa允許使用,6.4 MPa以下接受訂貨)

      壓力降Pressure drop

      0.02MPa

      壓力露點Pressure dew point

      -40(0.7MPa)(-60℃以下接受訂貨)

      再生方式Regenerative way

      無熱再生

      控制方式Control mode

      全電子可編程序時間控制

      工作周期Work cycle

      T=410分鐘(可調)

      再生氣量Regeneration gas

      13%~15%

      吸附劑Adsorbent

      活性氧化鋁

      進氣含油量Inlet oil content

      0.1PPM

      安裝方式Installation

      室內、無基礎,混凝土地面找平,環境溫度>0

       

      主要技術參數 Main technical parameters

      型號 Type(KXD-)

      0005

      0015

      0030

      0060

      0120

      0200

      0320

      0400

      0500

      0600

      0800

      1000

      1200

      處理量 Capacity m3/min

      0.6

      1.5

      3.6

      6.5

      13.5

      24

      32

      44

      55

      65

      87

      110

      130

      吸附劑填充量 Adsorbent filling quantity(KG)

      16

      38

      89

      160

      340

      590

      790

      1080

      1360

      1600

      2150

      2700

      3200

      外形尺寸

      Appearance

      and size

      L(mm)

      600

      800

      1000

      1400

      1600

      2000

      2100

      2300

      2480

      2550

      2600

      2800

      2830

      W(mm)

      310

      410

      500

      530

      640

      650

      710

      780

      1000

      1000

      1325

      1564

      1564

      H(mm)

      1050

      1500

      1600

      1600

      2260

      2760

      2800

      2900

      2950

      2950

      3180

      3416

      3672

      接口尺寸 Interface size

      ZG 1/2"

      ZG 1"

      ZG 1"

      ZG 1.5"

      ZG 2"

      DN65

      DN80

      DN80

      DN80

      DN80

      DN100

      DN100

      DN150

      凈重 Weight(kg)

      100

      140

      240

      400

      780

      1000

      1425

      1910

      2300

      2500

      3400

      4400

      5200

       

      久久久久亚洲AV无码